主燃孔对模型燃烧室流场的影响

为了深入了解主燃孔参数变化对双级轴向旋流器模型环形燃烧室内气流组织与气动性能的影响,采用PIV测速仪对该燃烧室内冷态和液雾燃烧流场进行测量,试验研究在冷、热态情况下不同主燃孔参数对模型燃烧室内回流区的形成、轴向平均速度u,轴向脉动速度Urms,雷诺剪切应力u′v′分布的影响。研究结果表明:主燃孔参数变化对燃烧室内冷、热态流场有着重要的影响;燃烧室在燃烧情况下所得的中心回流区长度要比冷态短,但回流负速度、脉动速度和雷诺应力都明显大于冷态,所得的研究结果可为燃烧室优化设计提供有用的依据。     

超燃冲压发动机控制方法

针对超燃冲压发动机地面试验和飞行试验的需求,本文论述了超燃冲压发动机控制的基本问题。在对这些基本问题认识的基础上,初步给出了超燃冲压发动机控制系统的基本框架,探索了控制任务的解决方案。主要包括推力控制、燃烧模态控制、进气道控制、调节/保护多回路切换控制和发动机/飞行器一体化协调控制。最后对超燃冲压发动机控制未来发展进行了展望。     

宇航用元器件锡晶须生长研究

通过分析锡晶须的研究历史,将锡晶须的研究归结为三个阶段:早期对锡晶须现象的研究、锡晶须生长机理的研究和减缓锡晶须生长方法的研究。比较了锡晶须长度及密度的测量方法。总结了目前抑制锡晶须生长的方法:在不同基底材料上采用不同厚度镀锡层;使用Ni、In等阻挡层;对镀层表面进行热处理和回流处理;避免使用纯锡镀层,镀层合金化;在镀层表面覆盖保形涂层。     

航天用复合材料压力容器的应用与发展

复合材料压力容器在航空航天、汽车、电子等领域具有广泛的应用,本文系统地分析了目前复合材料压力容器的材料和典型结构,阐述复合材料压力容器在航天工业的主要应用及发展方向。     

滚动轴承摩擦力矩的乏信息模糊预报

滚动轴承摩擦力矩的波动具有不确定性,属于概率分布与趋势规律都未知的乏信息系统.这阻碍了对轴承摩擦力矩的小样本分析与总体把握.为此,以模糊集合理论为基础,从小样本入手,建立了航天轴承摩擦力矩参数的经验概率密度函数及其模糊预报模型,并对摩擦力矩的均值上界和最大值上界进行预报.对HKTA和HKTB两种轴承摩擦力矩参数的试验研究表明,在99%～100%置信水平下,预报结果与试验结果之间的误差很小,最大绝对误差仅为0.081 1个设定单位,最大相对误差仅为10.165%,可以满足航天工程的要求.      

利用上游斜坡改善气膜冷却效率的数值研究

为了获得气膜孔上游放置斜坡对气膜冷却效率的影响规律,采用数值模拟方法研究了斜坡的台阶高度分别为0.3D,0.5D,0.75D,1.0D和1.5D时不同吹风比下的流动过程和冷却效率分布情况,并与常规气膜孔冷却结构形式进行对比,以揭示斜坡对气膜冷却效率改善作用的影响机理。研究表明,在气膜孔上游设置斜坡,延缓了主流通过反向涡对对冷却气流的掺混作用,反向涡对强度减弱,冷却气流出流后的贴壁效果更好,提高了气膜冷却效率,随着吹风比的增加,斜坡高度较高时无论是在气膜孔中心线处还是在两气膜孔之间区域的冷却效率值都得到大幅度的提高。     

脉冲爆震发动机自吸气实现方式

根据脉冲爆震发动机工作循环过程中的压力变化特点,对脉冲爆震发动机自吸气的实现方式进行了探索研究,设计了几种不同的结构型式以改善尾部吸气质量,并进行了数值模拟。结果显示:单一等截面直爆震管虽然可以在爆震后管内负压作用下从尾部自吸气,但是吸入的基本全是尾气,无法用于再次爆震起爆;进、排气口分开有利于改善自吸气质量,进气口离排气口越远,尾气影响越小,吸气质量越好;进、排气口间最好有一定压差,否则会出现两端同时进气,形成吸气震荡,并在爆震管中部夹有燃气无法排出;利用设计的气动阀可以实现从爆震管前端自吸气,吸气结束后整个爆震管内充满新鲜空气,可以用于再次爆震起爆。     

Reduction in clamping force due to applied longitudinal load to aerospace structural bolted plates

The main purpose of the present work is to experimentally and numerically study why and how the magnitude of the bolt clamping force reduces in the aerospace structural bolted plates when they are subjected to a longitudinal tensile load. In the experimental method, a holed plate of aluminium alloy 7075-T6 was clamped using a single bolt fastener, and then tested under an increasing static longitudinal tensile load. The bolt clamping magnitude was determined by using the measured axial compressive strains of a steel bush placed between the nut and plate. Two clamped specimens with different initial clamping forces were studied. In each specimen the actual clamping forces were determined during the longitudinal loading on the plate. In the numerical method, a three-dimensional (3D) finite element model was generated in order to simulate and quantify the bolt clamping force in the plate model loaded in tension. Both experimental and numerical results showed that the clamping force reduces considerably in the aluminium bolted plates under the longitudinal tensile loading. This is because of the transverse contraction of the plate material that causes the clamped material to release from the initial compression, and as a result, the clamping force to relax.     

基于屏蔽数据的航空电源系统可靠性分析

当航空电源系统具有屏蔽寿命数据时,研究逆Weibull型部件可靠性的估计问题.利用Bayes方法和极大似然方法,给出了逆Weibull型部件可靠性的Bayes估计和极大似然估计.利用随机模拟方法对两种估计的结果进行了比较.     

Numerical investigation of the nonreacting and reacting flow fields in a transverse gaseous injection channel with different species

The mixing and combustion process has an important impact on the engineering realization of the scramjet engine. The nonreacting and reacting flow fields in a transverse injection channel have been investigated numerically, and the predicted results have been compared with the available experimental data in the open literature, the wall pressure distributions, the separation length, as well as the penetration height. Further, the influences of the molecular weight of the fuel and the jet-to-crossflow pressure ratio on the wall pressure distribution have been studied. The obtained results show that the predicted results show reasonable agreement with the experimental data, and the variable trends of the penetration height and the separation distance are almost the same as those obtained in the experiment. The vapor pressure model is suitable to fit the relationship between the penetration height, the separation distance and the jet-to-crossflow pressure ratio. The combustion process mainly occurs upstream of the injection port, and it makes a great difference to the wall pressure distribution upstream of the injection port, especially when the jet-to-crossflow pressure ratio is large enough, namely 17.72 and 25.15 in the range considered in the current study. For hydrogen, the combustion downstream of the injection port occurs more intensively, and this may be induced by its smaller molecular weight.